Experimental Procedures: Put on all safety equipment and tie back loose hair or clothing before operating machine Check to make sure all parts of machine are working and functioning properly Double check all measurements for operating machine on work piece If spindle speed needs to be changed, (User Manual, p. 10-11)
• Stand to one side and switch on grinder. • Ensure the grinder operates smoothly and does not vibrate. If you notice any unusual vibrations or noises, STOP. Re-inspect the grinder and fix the problem immediately. 7. Grinding • Use both hands to maintain hold of the grinder. • Allow grinder to reach full rpm before grinding.
• Be alert and cautious when a grinding operation requires locating fingers close to the wheel. • Feed the stock into the wheel with light to medium pressure. Do not force the piece. • Do not use the side of the grinding wheel to shape stock. • Stand erect in front of the grinder with both legs straight and slightly apart. Avoid stooping
Bench Grinder Operating Procedures 1. Inspect & Adjust Grinder Ensure area around grinder is clean and well maintained. Side guard must cover the spindle, nut and flange and 75% of the abrasive wheel diameter*. Check the work rest gap must be no greater than 1/8 inch adjust if necessary*.
Feb 02, 2016· Ball Mill and Grinding Circuit Preparation for Start-UP The following items must be checked before the equipment in the Grinding Circuit is started. Check the ore slot feeder for obstruction or hang—ups. Check the ball mill belt feeder for undue buildup of material. Check oil level in ball mill lube oil tanks. Also, check grease level in the mill ring gear spray lube drum. Ensure that the
Operating Procedure 1. Inspection Before using the polisher/grinder inspect it and its surroundings for the following: C Make sure the electric power connections are made correctly and that the power cable is not damaged. C Make sure the polisher/grinder, including the wheel and the bowl, are clean. C Make sure the table and the floor around the table are clean and dry.
Nov 02, 2009· STANDARD OPERATING PROCEDURE ‘S.O.P’ After stopping the machine, use a brush or rag to remove all excess chips from the mill bed and stock. Use a rag or Kevlar gloves to handle sharp cutting tools. Cutting tools must be securely fastened in the machine spindle with the proper accessory. Never try to tighten cutting bits or tools by hand.
Describe standard operation principles for the grinding processes recognise the raw materials influence on grinding performance outline start amp stop procedures and standard operating procedures identify the standard mill instrumentation describe the standard interlockings and normal alarm limits relate the working principle of the
grinding of 6hi mill rolls by asian rewari 2020-01-07; Hammer Mill: Standard Operating Procedures 1 Hammer mill must not be operated solo At least two workers must be present when the mill is in use Operators must wear eye and hearing protection as well as nuisance dust at all times when operating the mill Operators must inform
Hammer Mill Standard Operating Procedures 1 Hammer mill must not be operated solo At least two workers must be present when the mill is in use Operators must wear eye and hearing protection as well as nuisance dust at all times when operating the mill Operators must inform project leader when mill will be used 2. Learn More SAFETY OPERATING PROCEDURES Bench Grinder
Bench Grinder Operating Procedures 1. Inspect & Adjust Grinder Ensure area around grinder is clean and well maintained. Side guard must cover the spindle, nut and flange and 75% of the abrasive
Operating Procedure 1. Inspection Before using the polisher/grinder inspect it and its surroundings for the following: C Make sure the electric power connections are made correctly and that the power cable is not damaged. C Make sure the polisher/grinder
Safe Operating Procedures This SOP should be used in conjunction with relevant machinery manuals and manufacturer recommendations. Procedure Reference Version Effective Date Review Date Page Number Date Printed WHS SOP 2 1.0 28/03/2018 28/03/2021 1 24/04/2018 SOP 02 Bench Grinder
grinding disc. Never make adjustments while the angle grinder is running. Do not switch off the angle grinder when it is under load, except in an emergency. Allow angle grinder to reach operating speed
3. Select the Right Devices and Implement Standard Operating Procedures . Being OSHA compliant is a great way to ensure lockout/tagout safety, but it is important to go above and beyond the key
o Adjust the tongue guard on the top side of the grinder to within ¼-inch (0.6350cm) of the wheel. o Adjust the tool rest to within 1/8- inch of the grinding wheel. • Before starting the grinder, inspect the