The ‘ aggregate crushing value test ` gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load under standardized conditions, and the strength of the aggregate used in road
The crushing value test is conducted on aggregates that are used for the construction of roads. Lower crushing value aggregates give much more durability for roads due to its lower crushed fraction under the compression load. The road is subjected to motion pressure continuously. So the aggregate used for road construction should be able to sustain that motion pressure.
1.Objective. The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggregate of aggregate crushing value 30 or higher, the result may be anomalous, and in such cases the ten percent fines value should be determined instead. 2.Apparatus Required.
Aug 11, 2020· It is recommended that the crushing value of aggregate should be less than 30%. If it is more than 30 % then 10% finer aggregate is suggested to use. The aggregate whose crushing value is less than 30% can be used for cement concrete road. The aggregate whose crushing value is less than 40% can be used for wearing surface. This test must be done before it comes to road and
We would like to show you a description here but the site won’t allow us.
May 22, 2020· The aggregate crushing value= B/A*100 . Where, B is weight of fraction passing 2.36mm sieve ; A is weight of surface dry sample taken in mould. Note. The aggregate crushing value should not be more than 45% for aggregate used for concrete other than the wearing surfaces. 30% for concrete used the surfaces such as runway, roads and air field pavements.
AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm
The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Crushing value is a measure of the strength of the aggregate. The aggregates should therefore have minimum crushing value. 3. APPARATUS
Mar 24, 2013· Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.
Crushing strength, impact value abrasion resistance, and elastic modulus of aggregate are interrelated properties that are greatly influenced by porosity. Aggregates from natural sources that are commonly used for making normal-weight concrete, are generally dense and strong; therefore they are seldom a limiting factor to strength and elastic properties of concrete.
Aggregate crushing value test provides the resistance of an aggregate sample to crushing under gradually applied compressive load. Generally, the test is conducted on aggregate passing 12.5 mm and retained on 10 mm sieve.
Apr 10, 2012· The aggregate crushing value provides a relative measure of resistance to crushing under gradually applied compressive load. Lesser the aggregate crushing value stronger is the given sample of aggregates. Object: To determine aggregate crushing value by compressive testing machine. Apparatus required: 1. Steel cylinder open with both ends. 2.
Crushing resistance of coarse aggregate is the key to the stability and durability of the skeleton structure of permeable asphalt (PA) mixture. To determine the technical requirements of crushing value of coarse aggregate used in PA mixture, step-loading compression tests were conducted on the mixtures of PA-13 and a control asphalt mixture AC-13, respectively.
Calculate Aggregate Crushing Value. The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = W B W A × 100. Where, W A is weight of surface-dry sample
number. Report the mean as the Aggregate Crushing Value, unless the individual results differ by more than 0.07 times the mean value. In this case repeat the test on two further specimens, calculate the median of the four results to the nearest whole number and report the median as the Aggregate Crushing Value. A data sheet is given as Form 7.7.1.
aggregate crushing value indicates strong aggregates, as the crushed fraction is low. ~hus the test can be used to assess the suitability of aggregates with reference to the crushing strength for various types of pavement components. The aggregates used for the surface course of
Mar 24, 2013· Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.
Jan 13, 2011· AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm
Nov 21, 2016· AGGREGATE PROPERTIES Ideal Aggregate: Neither Elongated Nor Flaky 13. AGGREGATE PROPERTIES • Mechanical Properties: Crushing strength, impact value abrasion resistance, and elastic modulus of aggregate are interrelated properties, that are greatly influenced by
the aggregate product. PRODUCT QUALITY If deleterious material exists at undesi rable levels after crushing and may be identified as being predominantly in one size range that is not needed for product size, the material may be screened out (namely, fines or top size). This step may occur between crushing so that an opportunity exists to
The aggregate crushing value (ACV) of an aggregate is the mass of material, expressed as a percentage of the test sample. which is crushed finer than a 2,36 mm sieve when a sample of aggregate passing the 13,2 mm and retained on the 9,50 mm sieve is subjected to crushing under a gradually applied compressive load of 400 kN. 2 APPARATUS 2.1 An
Calculation of aggregate crushing value. The aggregate crushing value is defined as the ratio of the weight of fines passing through specified IS (here 2.36mm sieve) to the total weight of sample expressed in percentage. W1= Weigh of the total aggregates (Wa-We) W2= Weigh of aggregates passing through 2.36mm IS sieve.
May 08, 2013· Objective For determination of the aggregate crushing value of coarse aggregate, which passes 12.5 mm. IS sieve and retained on 10 mm. IS sieve. Reference Standard IS: 2386 (Part IV)-1963 Methods of test for aggregate for concrete Part IV Mechanical Properties. Equipment & Apparatus Steel Cylinder Sieves (12.5mm,10mm) Cylindrical metal measure Tamping Rod Balance (0
BS 812 part 110 describes a method to determine the aggregate crushing value (ACV) which gives a relative measure of the crushing resistance of aggregate under an increasing compressive load.The method is applicable to aggregates passing a 14.0 mm test sieve and retained on a 10.0 mm test sieve.